The Vandy Vape Kylin M RTA comes during a typical packaging – an old fashion black cardboard box featuring a picture of the RTA on the front, and a listing of contents, also as company information and a handy diagram for installing the coil and wicking, on the rear . If you’re one of those few folks that basically check the authenticity of their products online, there’s a scratch-and-check seal on the side of the box.
Inside the box we’ve the Kylin M RTA placed next to a spare bubble glass and two plastic cases that kind of appear as if microchips initially glance. They’re actually just plastic boxes, each containing a couple of of of varied mesh strips that you simply simply simply simply can use as coils. So you get four coils included within the kit, which is pretty generous considering some manufacturers don’t bother including any coils within the littlest amount , mesh or otherwise.
Also within the box you’ll find a bag of accessories – spare o-rings, screws and comes for the build deck, alittle screwdriver, 510 drip tip adaptor, and a cylindrical piece of metal that acts as a coil jig – a user manual and two cotton laces that make wicking this RTA slightly easier than regular cotton.
The new Kylin M retains the general design of the primary Vandy Vape Kylin RTA, but incorporates some huge-enough changes to face out as a completely different device. the primary main difference you notice is that the honeycomb-pattern top airflow system that replaces the lowest airflow of the first Kylin. That’s actually the only visible difference. The 810 resin drip tip is analogous thereto of the old Kylin, the knurling on absolutely the best cap and thus the lowest is that an equivalent , and even the chimney has the same design. Things are much different on the within , so this definitely less of the same .
The Kylin M RTA measures 34mm-long and 24mm in diameter, making it slightly shorter than the previous atomizers during this line, and is currently available in seven different colors. I received the Frosted Grey version for this review, which looks pretty cool if you prefer a matte finish. There’s also gold and rainbow if you’d wish to face out.
At absolutely the best we’ve a typical 810 resin drip tip that you simply simply simply simply can swap out for the opposite 810, or even a 510 with the included adapter. Ten we’ve absolutely the best cap which unscrews to reveal one of the deepest fill-ports I even have ever seen on an atomizer. The holes are located at the lowest of a reservoir, right where the glass section of the tank starts, which actually allows you to fill past the fill ports if you’d wish to , because there’s such tons room between the tank and thus the absolute best cap. It’s an interesting design, although not very practical, in my opinion.
Right under absolutely the best cap we’ve the airflow control ring featuring honeycomb-pattern slots. you’ll remove the ring to work out out the actual airflow slots dig the atomizer. they’re curved at an angle, almost like those on the very fashionable Dead Rabbit RDA so as that they hit the mesh coil directly for max flavor. These are massive airflow slots, though, and unless you’ve super strong lungs, you’ll mist likely feel the need to shut the airflow to half, at the very least. WOTOFO Recurve Dual RDA
The tank section looks pretty ordinary, apart from the visible fill holes at absolutely the better of the chimney, then does rock bottom section, which simply seals off the tank and features a non-adjustable, gold-plated pin at the lowest .
As i discussed, on the within the Kylin M is extremely different than its predecessors. The M stands for Mesh so this features an inside design meant to accommodate mesh strips rather than the
usual metal coils we’ve all been using for over a decade now. Vandy Vape has some experience during this field, with two previous devices – the Mesh RDA and Mesh RTA – designed with mesh in mind, but they weren’t the foremost successful devices. For one, they weren’t the only things to make on, but now around all Vandy Vape had to undertake to was borrow someone else’s idea.
As is typically the case when Chinese companies are involved, copyright isn’t vital . an organization will just take another’s design, improve thereon slightly and use it as its own. That’s a controversial practice within the West, but there’s no denying that it’s beneficial for the absolute best user. It sometimes makes things cheaper, other times it makes them better, and thus the Kylin M RTA could even be a significant example.
As a connoisseur, watching the build deck of the Kylin M, you’d think it had been that of the Wotofo Profile Unity RTA, and technically, you would be right. Vandy Vape took the design of the Profile Unity build deck, made it slightly better by adding springs to the clamp system to possess them retract automatically, and adding some barriers that prevent the mesh from falling into rock bottom . They also implemented top-airflow, whereas the Profile Unity uses bottom airflow. So while the deck looks the same on both devices, it’s actually different, sort of.
I’ve never been a devotee of mesh RTAs and RDAs simply because I found fixing the strips a pain within the behind. That wasn’t the case with the Vandy Vape Kylin M, though. because of the slight changes to the design of the build deck, this thing is super easy to line up. albeit you’ve zero experience building and installing coils, you’d wish to be able to get this atomizer ready for vaping.
First things first, inform require the Kylin M apart and wash all the parts thoroughly. Companies claim to scrub their devices themselves, but it’s commonplace to hunt out machining oil residue once you’re taking atomizers apart. So give all the components an honest rinse with warm water and either allow them to dry overnight or use a paper tissue. Lost Vape Orion DNA Go Pod Cartridges
Once you’re ready to build, take one of the four bits of mesh included within the Kylin M kit and thus the cylindrical piece of metal from the accessories bag. Just bend the strip around the metal and you land up with a mesh arch that matches perfectly within the clamps of the build deck. Once the mesh is all bent up, unscrew the screws on the clamps to open them and just drop the mesh in there. Then gently place a finger over the mesh arch to hold it in place as you screw the clamps shut again. And that’s all there’s thereto .
Of course, there’s more to this atomizer than installing the mesh coils. Wicking is crucial to a satisfying vaping experience, and Vandy Vape knows this, which is why they printed a diagram of how you’re imagined to cut the cotton so on seal the juice slots at the lowest of the build deck. I’d add that you simply simply simply simply want to make sure the cotton strips aren’t too thick, as this is often often often often a top-airflow atomizer, therefore the prospect of leaking is virtually zero. you will get some gurgling or spit-back if juice floods the atomization chamber, but that basically wouldn’t be a disaster. Plus, if you get enough cotton up against the juice flow holes, you’d wish to be fine.
The problem with employing plenty of cotton, as I’ve seen in several YouTube tutorials is that it opens you up to the danger of dry burning. These mesh strips have an outsized area compared to regular coils, so if you raise the facility output slightly an excessive amount of , the cotton struggles to saturate enough to catch au courant the fast atomization. By combing the cotton to thin it out slightly , you create it easier for the juice to realize the coil faster. That has been by experience with this device, anyway.
Whichever way you opt on to undertake to thereto , it’s pretty darn easy, and every one thanks to the Profile Unity build deck and thus the enhancements Vandy Vape made thereto .
I didn’t have much experience with mesh RTAs, which i certainly hadn’t tried the Wotofo Profile Unity, so I didn’t really know what to expect from the Vandy Vape Kylin M.
One thing ready to |i’ll”> ready to |i’ll”> i will be able to be able to be able to say is that no matter which sort of mesh you’re using, your vaping experience are becoming to be about an equivalent . That applies to the 2 sorts of mesh included within the kit, but there are three more advertised on the Vandy Vape website which may impact your vaping more significantly. Both sorts of mesh strip within the kit are labelled ‘Ai M Coil’, which may be slightly weird since one has significantly smaller holes (so more surface area) than the opposite , and different resistance 1.5Ω compared to 2.0Ω, but within the highest the recommended wattage range is comparable (50W – 70W vs. 40W – 60W), therefore the vaping experience isn’t radically different between the 2 .
Mesh is typically related to better flavor, a minimum of as compared to plain coils, but I personally think vapor production is that the foremost strength of the Kylin M RTA. Even at lower wattage, this thing produces crazy amounts of vapor, no matter which sort of mesh you’re using. it’s sensible , because mesh features a much bigger area than regular coils so it vaporizes liquid faster, but still, it’s pretty impressive to work out just what proportion vapor you’ll chug.
Flavor depends tons on how well you wick your mesh coil. Put slightly an excessive amount of cotton and flavor becomes muted, especially if you’d wish to chain vape – take multiple hits in succession – and you run the danger of burning the cotton also . If you thin the cotton enough to permit the juice to realize the component faster, you would like to urge some very nice flavor out of of the Kylin M. Of course, you’ll want to tweak the airflow slightly also . I found that leaving it just 1 / 4 open is true for optimizing flavor, but it all depends on personal taste. Definitely don’t leave it wide open though, it’s way too airy that way.
The Kylin M produces monster clouds of vapor and above average flavor under the proper conditions, but you’ll need to buy it in juice. This thing is one thirsty RTA. It actually takes me back to the times of the SMOK TFV8/TFV12 days when sub-ohm tank needed topping off after a couple of of hits. a minimum of a short time past you were pumping over 100W into the coils, but the Kylin M burns through juice even at medium wattage levels. Again, it’s to undertake to to with the large area of the mesh strip, so there’s nothing you’ll do about it.
So as long as you’re happy burning through juice for a mouthful of tasty vapor, you would like to enjoy using the Kylin M. I wish it had a way bigger juice capacity – it holds only 4.5ml with the bubble tank – but aside from that, I can’t really consider an enormous con. Some people may have a drag with the “borrowing” of the Profile Unity build deck, but I for one haven’t any such issues. Vandy Vape made it better and adapted it to their top-airflow RTA.
If you’re trying to hunt out a high-quality, leak-proof mesh RTA that’s also extremely easy to form on, the Vandy Vape Kylin M should be at the absolute best of your list. The Wotofo Profile Unity is certainly a top contender also , but it’s tons taller, trickier to form on and has bottom airflow, which makes it susceptible to leaking. At the very best of the day both devices have their pros and cons, but you actually shouldn’t knock the Kylin M as a knockoff, because it’s definitely a totally different atomizer than the one that inspired it.