NRX Disposable Pod System Best Review

Recently, I even have receive an item NRX DISPOSABLE POD SYSTEM. The starter kit comes crammed with an NRX Air device, two pre-filled pods, a quick but rather nice braided USB type-C cable and a user manual. It’s available in midnight black, navy, pearl white, red and teal mint. a very simple kit but everything you’d need to start is included.
The NRX Air could even be a draw activated disposable pod device with a built-in 350mAh battery. On one side it is the letters NRX with the X lighting up to point when it’s firing, charging and thus the battery status. it’s a consistent size and shape to many other pod systems slightly slightly slightly slightly slightly a bit like the Juul or Stlth but with one distinguishing factor, it uses USB type-C to charge rather than a proprietary connector or micro USB. As more and more tech manufacturers switch to USB type-C it’s just that much more convenient to carry around however the device doesn’t support quick charge so relying on the charger your cable is connected thereto won’t work and you will need to plug it into a lower powered device slightly slightly slightly slightly slightly a bit like the USB port of a PC. A typical charge takes 45mins but the device tends to last me the entire day and typically then some.

Aside from the charge port there really isn’t much else to differentiate it from the countless others. There isn’t any quite airflow control and air to the pod comes via two tiny holes one on all sides but even covering them up the draw stays fairly tight. The draw activation is smooth an consistent then far I haven’t had one issue with it misfiring. actually many who possesses to undertake to to with leaking and that’s another thing that so far after fortnight of constant testing I haven’t had one drop leak . As for output regulation, on their product page they mention a wise AI chip that controls the voltage and pod-specific power for consistent flavour, hits and performance therefore the output is regulated and consistent which on behalf of me is typically a huge plus.  NRX DISPOSABLE POD SYSTEM

The pods that accompany the kit are made up of PCTG plastic, hold 1.5ml of liquid each and appear to return during a typical strengths of three or 4% of salt based nic. they’re available in neat little plastic containers with a silicone plug holding them in and are sealed on either end with tiny silicone plugs within the particular pod so you recognize they’re getting to be dust free once you attend use them. There are actually two kinds of pods which can be purchased for the device and one of each comes with the kit. One type uses ceramic coils and thus the opposite appears to use a more traditional cotton based coil. I find it hard to differentiate the two and unless you see it listed on their product page you likely wouldn’t know there’s a difference. They also use a double layer isolation technology that helps to reduce pressure and stop leaking then far they rise up to the hype.

They also mention a replacement quite atomization technology and from the images on their site it appears to be some quite mesh sandwiched inside their atomizer heads. So far, performance has been absolutely solid and thus the output and flavour i buy from these pods is smooth and full. I did mention that the device appears to be originally geared towards an Asian market so being half Japanese myself the list of flavours and thus those i’d wish to undertake really appeal to me which i imagine they’ll also do well in areas like Vancouver and Toronto. TastyClouds were kind enough to send some samples so I’ll list the flavours i attempted and initial thoughts below:

Iced Lychee(included with kit): one of the default flavours within the kit, it’s a satisfying light lychee flavour with a light-weight hit of ice. Fairly subtle for lychee but nice and refreshing. DTL DISPOSABLE 8 Flavor

Tieguanyin Tea(included with kit): one of my favourites from the bunch and another default flavour. It’s a sort of Oolong tea that’s really spot on but it also includes successful of ice on the exhale.

Apple Sorbet: one of the milder flavours within the set. It’s a satisfying clean and easy apple flavour again with a lightly iced exhale.

Mung Bean Popsicle: This one will seem weird to many westerners but mung could even be a well-liked flavour within the East. This one to me is pretty spot on also and really tastes like mung which to many may remind them slightly of soy milk but with a fairly strong hit of ice. a very unique flavour and one that many Asians will likely appreciate.

Ultra Cola: You can’t have a pod system without a cola flavour and this one is pretty straightforward. It tastes like cola but with a light-weight hit of ice on the exhale. Disposable Vape Starter Kit

Watermelon: This one is another somewhat standard and straightforward flavour, it’s watermelon. It’s not too sweet and is additionally amid a very light ice on the exhale. This one may have the lightest ice of the set.

ICE BRG: ChewChew Grape: This was another favorite of mine from the bunch. It’s basically a grape Hi-Chew. A chewy candy that’s really popular in Asia and this rendition is spot on. It too features a really slight ice on the exhale but pretty mild compared to the others.

ICE BRG: Ripe Mango: Funny enough I find the ICE BRG pods to possess less ice in them than the others. As this ripe mango is simply about just a satisfying tasting ripe mango with just a very Very light ice on the exhale.

ICE BRG: Sweet Lychee: I quite expected this one to be a repeat of iced lychee but I actually get considerably more lychee flavour from this one and maybe slightly less ice. I’m a huge fan of lychee so this was another one that basically peaked my interests!

You might have noticed alittle trend with these flavours. Every single one of them contains a minimum of slightly bit of ice which may be a haul for a couple of of of of of of . I personally don’t mind slightly of ice in my vapes and truly enjoy the refreshing hit they supply but I imagine some are getting to be turned off by it’s inclusion. aside from that, the flavour and performance of the NRX Air is on point which i haven’t had one issue with the device misfiring or the pods leaking. With interesting Asian inspired flavours like mung and Tieguanyin tea these really hit home on behalf of me , they even have a red bean flavour but sadly I wasn’t able to try all of them . Sure they won’t be for everyone but i do know many folks which may certainly appreciate what TastyClouds and NRX are bringing to the table!

First experience Vandy Vape Kylin M RTA 4.5ml 24mm

The Vandy Vape Kylin M RTA comes during a typical packaging – an old fashion black cardboard box featuring a picture of the RTA on the front, and a listing of contents, also as company information and a handy diagram for installing the coil and wicking, on the rear . If you’re one of those few folks that basically check the authenticity of their products online, there’s a scratch-and-check seal on the side of the box.
Inside the box we’ve the Kylin M RTA placed next to a spare bubble glass and two plastic cases that kind of appear as if microchips initially glance. They’re actually just plastic boxes, each containing a couple of of of varied mesh strips that you simply simply simply simply can use as coils. So you get four coils included within the kit, which is pretty generous considering some manufacturers don’t bother including any coils within the littlest amount , mesh or otherwise.
Also within the box you’ll find a bag of accessories – spare o-rings, screws and comes for the build deck, alittle screwdriver, 510 drip tip adaptor, and a cylindrical piece of metal that acts as a coil jig – a user manual and two cotton laces that make wicking this RTA slightly easier than regular cotton.
The new Kylin M retains the general design of the primary Vandy Vape Kylin RTA, but incorporates some huge-enough changes to face out as a completely different device. the primary main difference you notice is that the honeycomb-pattern top airflow system that replaces the lowest airflow of the first Kylin. That’s actually the only visible difference. The 810 resin drip tip is analogous thereto of the old Kylin, the knurling on absolutely the best cap and thus the lowest is that an equivalent , and even the chimney has the same design. Things are much different on the within , so this definitely less of the same .
The Kylin M RTA measures 34mm-long and 24mm in diameter, making it slightly shorter than the previous atomizers during this line, and is currently available in seven different colors. I received the Frosted Grey version for this review, which looks pretty cool if you prefer a matte finish. There’s also gold and rainbow if you’d wish to face out.

At absolutely the best we’ve a typical 810 resin drip tip that you simply simply simply simply can swap out for the opposite 810, or even a 510 with the included adapter. Ten we’ve absolutely the best cap which unscrews to reveal one of the deepest fill-ports I even have ever seen on an atomizer. The holes are located at the lowest of a reservoir, right where the glass section of the tank starts, which actually allows you to fill past the fill ports if you’d wish to , because there’s such tons room between the tank and thus the absolute best cap. It’s an interesting design, although not very practical, in my opinion.

Right under absolutely the best cap we’ve the airflow control ring featuring honeycomb-pattern slots. you’ll remove the ring to work out out the actual airflow slots dig the atomizer. they’re curved at an angle, almost like those on the very fashionable Dead Rabbit RDA so as that they hit the mesh coil directly for max flavor. These are massive airflow slots, though, and unless you’ve super strong lungs, you’ll mist likely feel the need to shut the airflow to half, at the very least. WOTOFO Recurve Dual RDA
The tank section looks pretty ordinary, apart from the visible fill holes at absolutely the better of the chimney, then does rock bottom section, which simply seals off the tank and features a non-adjustable, gold-plated pin at the lowest .

As i discussed, on the within the Kylin M is extremely different than its predecessors. The M stands for Mesh so this features an inside design meant to accommodate mesh strips rather than the

usual metal coils we’ve all been using for over a decade now. Vandy Vape has some experience during this field, with two previous devices – the Mesh RDA and Mesh RTA – designed with mesh in mind, but they weren’t the foremost successful devices. For one, they weren’t the only things to make on, but now around all Vandy Vape had to undertake to was borrow someone else’s idea.

As is typically the case when Chinese companies are involved, copyright isn’t vital . an organization will just take another’s design, improve thereon slightly and use it as its own. That’s a controversial practice within the West, but there’s no denying that it’s beneficial for the absolute best user. It sometimes makes things cheaper, other times it makes them better, and thus the Kylin M RTA could even be a significant example.

As a connoisseur, watching the build deck of the Kylin M, you’d think it had been that of the Wotofo Profile Unity RTA, and technically, you would be right. Vandy Vape took the design of the Profile Unity build deck, made it slightly better by adding springs to the clamp system to possess them retract automatically, and adding some barriers that prevent the mesh from falling into rock bottom . They also implemented top-airflow, whereas the Profile Unity uses bottom airflow. So while the deck looks the same on both devices, it’s actually different, sort of.
I’ve never been a devotee of mesh RTAs and RDAs simply because I found fixing the strips a pain within the behind. That wasn’t the case with the Vandy Vape Kylin M, though. because of the slight changes to the design of the build deck, this thing is super easy to line up. albeit you’ve zero experience building and installing coils, you’d wish to be able to get this atomizer ready for vaping.

First things first, inform require the Kylin M apart and wash all the parts thoroughly. Companies claim to scrub their devices themselves, but it’s commonplace to hunt out machining oil residue once you’re taking atomizers apart. So give all the components an honest rinse with warm water and either allow them to dry overnight or use a paper tissue. Lost Vape Orion DNA Go Pod Cartridges

Once you’re ready to build, take one of the four bits of mesh included within the Kylin M kit and thus the cylindrical piece of metal from the accessories bag. Just bend the strip around the metal and you land up with a mesh arch that matches perfectly within the clamps of the build deck. Once the mesh is all bent up, unscrew the screws on the clamps to open them and just drop the mesh in there. Then gently place a finger over the mesh arch to hold it in place as you screw the clamps shut again. And that’s all there’s thereto .

Of course, there’s more to this atomizer than installing the mesh coils. Wicking is crucial to a satisfying vaping experience, and Vandy Vape knows this, which is why they printed a diagram of how you’re imagined to cut the cotton so on seal the juice slots at the lowest of the build deck. I’d add that you simply simply simply simply want to make sure the cotton strips aren’t too thick, as this is often often often often a top-airflow atomizer, therefore the prospect of leaking is virtually zero. you will get some gurgling or spit-back if juice floods the atomization chamber, but that basically wouldn’t be a disaster. Plus, if you get enough cotton up against the juice flow holes, you’d wish to be fine.

The problem with employing plenty of cotton, as I’ve seen in several YouTube tutorials is that it opens you up to the danger of dry burning. These mesh strips have an outsized area compared to regular coils, so if you raise the facility output slightly an excessive amount of , the cotton struggles to saturate enough to catch au courant the fast atomization. By combing the cotton to thin it out slightly , you create it easier for the juice to realize the coil faster. That has been by experience with this device, anyway.
Whichever way you opt on to undertake to thereto , it’s pretty darn easy, and every one thanks to the Profile Unity build deck and thus the enhancements Vandy Vape made thereto .
I didn’t have much experience with mesh RTAs, which i certainly hadn’t tried the Wotofo Profile Unity, so I didn’t really know what to expect from the Vandy Vape Kylin M.
One thing ready to |i’ll”> ready to |i’ll”> i will be able to be able to be able to say is that no matter which sort of mesh you’re using, your vaping experience are becoming to be about an equivalent . That applies to the 2 sorts of mesh included within the kit, but there are three more advertised on the Vandy Vape website which may impact your vaping more significantly. Both sorts of mesh strip within the kit are labelled ‘Ai M Coil’, which may be slightly weird since one has significantly smaller holes (so more surface area) than the opposite , and different resistance 1.5Ω compared to 2.0Ω, but within the highest the recommended wattage range is comparable (50W – 70W vs. 40W – 60W), therefore the vaping experience isn’t radically different between the 2 .
Mesh is typically related to better flavor, a minimum of as compared to plain coils, but I personally think vapor production is that the foremost strength of the Kylin M RTA. Even at lower wattage, this thing produces crazy amounts of vapor, no matter which sort of mesh you’re using. it’s sensible , because mesh features a much bigger area than regular coils so it vaporizes liquid faster, but still, it’s pretty impressive to work out just what proportion vapor you’ll chug.
Flavor depends tons on how well you wick your mesh coil. Put slightly an excessive amount of cotton and flavor becomes muted, especially if you’d wish to chain vape – take multiple hits in succession – and you run the danger of burning the cotton also . If you thin the cotton enough to permit the juice to realize the component faster, you would like to urge some very nice flavor out of of the Kylin M. Of course, you’ll want to tweak the airflow slightly also . I found that leaving it just 1 / 4 open is true for optimizing flavor, but it all depends on personal taste. Definitely don’t leave it wide open though, it’s way too airy that way.
The Kylin M produces monster clouds of vapor and above average flavor under the proper conditions, but you’ll need to buy it in juice. This thing is one thirsty RTA. It actually takes me back to the times of the SMOK TFV8/TFV12 days when sub-ohm tank needed topping off after a couple of of hits. a minimum of a short time past you were pumping over 100W into the coils, but the Kylin M burns through juice even at medium wattage levels. Again, it’s to undertake to to with the large area of the mesh strip, so there’s nothing you’ll do about it.
So as long as you’re happy burning through juice for a mouthful of tasty vapor, you would like to enjoy using the Kylin M. I wish it had a way bigger juice capacity – it holds only 4.5ml with the bubble tank – but aside from that, I can’t really consider an enormous con. Some people may have a drag with the “borrowing” of the Profile Unity build deck, but I for one haven’t any such issues. Vandy Vape made it better and adapted it to their top-airflow RTA.
If you’re trying to hunt out a high-quality, leak-proof mesh RTA that’s also extremely easy to form on, the Vandy Vape Kylin M should be at the absolute best of your list. The Wotofo Profile Unity is certainly a top contender also , but it’s tons taller, trickier to form on and has bottom airflow, which makes it susceptible to leaking. At the very best of the day both devices have their pros and cons, but you actually shouldn’t knock the Kylin M as a knockoff, because it’s definitely a totally different atomizer than the one that inspired it.

Experience of Vaporesso XTRA AIO Pod Kit 900mAh 2ml

I’ve get Vaporesso XTRA AIO Pod Kit 900mAh 2ml for a couple of weeks now which i’m thoroughly impressed by just how well this pod works. The new Vaporesso Xtra follows the drop by pod approach to its design, with easy to swap magnetic base pod cartridges, but that’s where the pod device similarities end. a singular shape, fantastic flavor production, unprecedented material, and durable 900mAh battery make the Xtra my top pick because the only pod device of the year so far!
So let’s get into it already, I’m sure you’re wanting to hear why the Xtra is such a fantastic pod device!
The Vaporesso Xtra brings an entire New Look to the pod device world, from its asymmetrical rounded edges to the unique fabric material, I can’t say enough goodies about how the Xtra is meant . the primary thing I noticed once I pulled this device out of its box was the woven texture on the non-metallic side of the pod. I can’t consider one vape device out there that utilizes a cloth material as decorative design and I’m loving it. There’s a satisfying textured feel to running your fingers across the surface of the pod, smoothy transitioning from a slick metallic finish to the silk-like fabric panels.
The rounded edge, while slightly funny watching first, makes complete sense once you decide on up the device. It’s designed in such the thanks to contour to the within curve of your fingers while you hold it. It even comes equipped with a sturdy attachment point for lanyards so you’ll wear it around your neck during hiking and vape hands-free if you’d wish to .
One puff off the Vaporesso Xtra had me sold on the coil quality. I’m unsure what cotton they’re using, but whatever it’s that’s within the coils is giving the Xtra crystal clear E-Liquid taste. i attempted a couple of of varied vape juice flavors with this pod, starting from tropical fruit to sweet dessert, and each time i used to be getting almost the precise same flavor as i’d from dripping those flavors onto an RDA. If you’re a flavor chaser looking to exchange your Uwell Caliburn I’d say give the Xtra a try, the flavour production is true on par with the Caliburn/Koko pods. Vaporesso XTRA Replacement Meshed
A long-lasting 900mAh internal battery provides hours of power for all of your vaping needs. Actually, unless you’re vaping 50mg salt nic 24/7, you would like to seek out that the Xtra lasts about 2-3 days in-between recharging.
So as far as pod devices go i feel I’ve made my opinions clear over the last few years. The GeekVape Biden, with its dual coil cartridges, had the sole flavor production out of any pod device at the time. Then came the Caliburn and Koko pod devices from Uwell and suddenly you’ll get almost nearly nearly nearly as good of a flavor profile because the Bident without trading in kidneys to buy for coils. Now with the Xtra, i feel it’s time to feature another device to my better of pods list, this is often often often one among the few vaping devices that I gave full 5/5 marks for once i wont to be doing internal testing. I highly recommend you check the Vaporesso Xtra out when it hits our shelves.

YUHETEC 8-in-1 Vape Coil

The Xtra is pod mod that’s made up of metal, unlike the plastic of the Osmall. The C-frame chrome body features a thick rubberized resin decal that elevates the planning and increases the security of your grip. The decal part could even be slightly cheap though. If you’re a picker like me, you’d possibly want to remain away from the edges of the sticker. Luckily it feels good within the hand and it’s well placed. The Xtra overall could even be a good-looking little pod mod. kind of the colors are often a fingerprint magnet, but the execution is tasteful.
Although the name of the device suggests otherwise, the Xtra is actually shorter than the Osmall, but much heavier. The Osmall is under 25 g and thus the Xtra is 60 g. It only measures 14 mm x 37 mm x 64 mm. I should means there’s an influence button on the lowest of the device. It’s not for firing; it’s just an on/off button turned on via a quick 5-click.
The kit comes with both Unipods, a Meshed 0.8-ohm loose MTL and a 1.2-ohm MTL (at least that’s how its advertised). The mouthpiece is analogous to the Osmall and derivative of the Renova Zero and SMPO, but much smaller. Also, the pods have a satisfying refill plug that cannot be totally removed, unlike the Osmall. The low resistance coil features a red plug and thus the MTL coil features a gray plug. i prefer that clear distinction between the two pods. The resistance is additionally written on the side of the pod opposite the plug.
Under the plug could even be a refill opening measuring about 3.5 mm x 5 mm. I’ve been filling it with pipette droppers and haven’t had a drag , though using high VG requires you to kinda snake the liquid in at an angle. All modern droppers like unicorns work perfectly no matter the viscosity of juice used.
The Unipods are magnetized drop in pods. They’re easy to urge obviate yet held in firmly thanks to a deeper seating and larger diameter magnets. this is often often often often an area I’m happy to figure out Vaporesso improve on. Their previous devices like this had magnets so weak they’d fall out if you said “boo.” I can devour the whole Xtra—all 60 grams of it—by the pod without the magnets failing. Even with fairly vigorous shaking, it stays connected. Of course, there’s limits and it’s not meant to be held like that. Also, there’s slightly of flexibility with the pod within the pod housing. It’s not enough to even be a con on behalf of me though because it only wiggles once you plan to look the hay . When you’re just taking successful or just holding it in between your lips, it doesn’t stationary.
The Xtra has been performing well, though I had hoped for the same performance on the 1.2-ohm coil as I got from the Osmall. I wasn’t sure what the performance might be with the Meshed 0.8-ohm coil, but i wont to make sure the MTL would be my favorite. Okay, so i wont to be wrong.
Meshed 0.8-ohm coil: Warm, clean, and fairly saturated flavor for such slightly device. Even with long drags, the flavour doesn’t get distorted. It wicks well like most mesh coils, but I’d recommend keeping ratios within the 50%-70% VG range. Another aspect that performs well with this coil is that the airflow. It’s a loose MTL that stays in its lane! It’s not slightly a bit like the Mi-Pod which struggles to understand that perfect middle ground of a loose MTL. i feel Vaporesso nailed this draw! i prefer better to recommend keeping nicotine to a max of 12 mg. Even you opt for 6 mg, it can still provides a solid throat hit…which is extremely good thing!
MTL 1.2-ohm coil: Though the specs are the same and thus the coils inside the pod look the same because the Osmall, the performance isn’t the same . And, frankly, I can’t tell a difference between the draw of this and thus the Meshed 0.8-ohm coil. I’d go so far on say that from the few pods that I’ve tried, the 1.2-ohm pod feels looser than the Meshed version. Either way, i feel this MTL is simply too loose especially for a single-strand coil. It wicks best with 50/50 and I’d recommend this with high nic up to 24 mg/mL or salts up to 36 mg/mL. the flavour is decent, but forgettable.
There haven’t been any hiccups with the Xtra pods. No leaking, spitting or flooding, though I haven’t tried to throw every viscosity at these coils like I did with the Osmall. I’d imagine you’d get flooding or gurgling with thin juice within the Meshed pods. Thin juice is fairly rare lately , so that’s not much of a priority . My main issue is that the 1.2-ohm coils struggle to put out notable flavor compared to the Osmall’s equivalent. But what the Xtra lacks in strict MTL vaping, it makes up for it with a flavorful loose MTL with the 0.8-ohm coils.
The Xtra charges through a micro USB port. I would’ve preferred a USB-C. But it’s pass-thru charging and an LED indicator to remain you clear on the status of your battery. Green is full, blue is midway, and red is almost depleted.
I’ve been impressed and fairly satisfied with the Xtra. The battery life is substantial for the power it pushes, the planning is clean, and thus the mesh pod satisfies. albeit i wont to be more interested in the MTL coils, because it seems , the Meshed coil was the star of the kit on behalf of me . I’m comfortable in recommending this device to anyone that prefers a loose MTL. albeit you don’t usually use pod devices, this could be a solid copy .

Vaporesso GTX One Vape Mod Comment

“GTX ONE may be a user-friendly MTL kit equipping GTX coils that give fresh flavour-boosting and rich cloud delivery. With an airflow system of the GTX TANK 18, it keeps the entire vaping catering to your required expectation. Furthermore, featuring Max 40W adjustable power supporting smart VW mode, the GTX ONE provides impressive vaping experience throughout. The 2000mAh built-in big battery comes with 2A Type-C USB allows longer endurance also as easier recharging. Leading the various others on flavour exploring journey, the compact GTX ONE is that the one that matches perfectly.” Vaporesso GTX One Vape Mod 2000mAh 40W
Without a spoiler alert I can honestly say Vaporesso’s description is totally honest and zip i might dispute, obviously slightly embellished but that’s to be expected from an advertising pitch.
GTX Coils
Adjustable Airflow & Power
Smart Variable Wattage
2000mAh Inbuilt Battery
2A USB Type-C Fast Charging
0.69” OLED Screen
Compact Ergonomic Design
Scratch-free Cover
18mm Diameter GTX ONE Tank
3ml (2ml TPD) Capacity
I will cover the above in additional detail later.
The GTX ONE kit comes within the customary quality and simplistic style box, the rear of the box lists the specs and therefore the box contents along side the scratch and check authenticity label. I don’t think I even have checked one among these for years but having received this kit from Vaporesso direct then i’m pretty confident its genuine!
There are not any notches within the lid so it’s a shake the bejesus out of it to open affair. Once you’ve got it open, you’re greeted with the highest layer containing the mod/battery, 18mm tank (0.8Ω Mesh preinstalled), and a spare straight glass with a baggie of spare seals. Lifting the highest compartment out, there’s another section containing the extra coil which is that the latest 1.2Ω Mesh coil. there’s a really top quality USB-C cable included and therefore the documentation within the sort of a rather thick, multi-language reference book is well detailed and illustrated.
rall the contents and packaging is spot on, no surprises but everything you’ll and will expect with a kit and zip omitted. Here’s the contents list:
I wasn’t expecting the GTX ONE kit within the least and it had been a mystery package in the post but I even have to admit i used to be delighted to what was inside. Bear in mind i used to be left wanting when it came to a real MTL adjustable airflow option using the GTX coils, the PM30 uses an equivalent coils but the airflow was just too loose on behalf of me . The last decent adjustable airflow MTL offering from Vaporesso was the Orca Solo Plus which I enjoyed, but when the new GTX coils came out and that i experienced the flavour from devices just like the XTRA pod, then it soon fell out of favour.
On the face of it the GTX ONE kit was EXACTLY what I had been looking for , even the color choice was to my personal preference. It’s not fairly often i buy excited by a replacement kit, but i used to be impatient to urge this kit photographed so I could get my grubby mitts thereon to vape.
While photographing, I had the prospect to look at the kits components, a couple of things that grabbed my attention that I liked:
The mod seemed a touch tall for a MTL (Mouth To Lung) offering, it’s noticeably taller than say the Target Mini 2 and about an equivalent height because the Target PM30, but it’s lighter and much easier within the hand. The textured coating felt really grippy and almost like the newest Gen and Swag mods.Vaporesso Renova Zero Pod Cartridge 2PCS
The all new GTX ONE 18mm tank was a moment like with its looks and size. Though it came with the 3ml bubble glass already fitted, I popped the 2ml straight glass on. i feel I prefer the straight glass but the bubble didn’t look too out of place either and a minimum of you get the choice (unless you get the TPD version). i actually just like the 510 drip tip as it’s a correct narrow bore MTL mouthpiece and is comfortable. The dominant black silicone seals actually increase the styling with the matching black tip. the most thing i used to be curious about were the GTX coils during a tank – at last!
I was already a lover of the new GTX coils for DTL (Direct Lung) within the PM80, the flavour and vapour from the subohm mesh coils are freakin’ superb. Not only that, but they last rather well . Having tested the MTL 1.2Ω regular and mesh within the PM30, I loved the flavour but the airflow was too loose on behalf of me therefore the GTX ONE tank should be a certainty .
*Compatibility Caution*
The only confusing thing is that not ALL GTX coils fit the GTX ONE tank. If you’re taking a glance at the compatibility chart below, you’ll notice the most difference; the lip under the lower seal is slightly larger and therefore the more obvious one is that the top. The incompatible coils are female fitting and therefore the newer compatible ones are male.
Now for pure MTL, this is often not a drag in the least because the only coils you’ll likely want to use are the four that are compatible, but it’s to travel down as a con as a more moderen vaper might get caught out when buying GTX coils. Vapefly Jester Vape Pod System Meshed Edition 1000mAh 2ml
The moment I had been expecting after getting the photos out of the way, I unscrewed the tank and fitted the 1.2Ω Mesh coil as that was the most one i used to be curious about . you’ll unscrew the bottom without taking the tank fully apart, the coil is Plug-n-Play press fit and really easy to swap. Priming the coil with a couple of drops of eliquid first is suggested , then screw the bottom back on.
Filling wasn’t as convenient as i might have liked. this is often done by unscrewing the highest cap, on the plus side you’ve got plenty of room to fill it up with none airlocks but you are doing need to confirm you don’t overfill or spill any juice into the coil bore. Once filled, simply screw the highest cap back on. It’s simple enough and easier than bottom filling old-school tanks, but it are often quite messy when out and about meaning you’ve got to carry the damp top cap in your hand. i assume i’m spoilt with latest generation slide to fill or maybe Vaporesso’s PTF filling.
Setting the airflow is completed via the AFC ring at the bottom of the tank. I found only one hole exposed was a pleasant tight draw, better still partially close one hole for a good tighter draw.
Once filled and allowing it 10-15 minutes to prime the coil, then it’s good to travel . Before you go hitting the hearth button, select your required wattage. By default, the wattage is about to five Watts, the 1.2Ω coil sweet spot was just about spot on to Vaporesso’s recommended wattage of 11 Watts, though my OCD had to vary it to 11.1 Watts. that basically is all you would like to try to to , dial within the wattage and vape.
As a beginner or a technophobe, then that’s really all you would like to recollect , but if you wish options then the primary (and only) option I enjoyed is that the SMART VW, basically this detects the coil that’s fitted and sets the wattage automatically to the recommended power.
*NOTE* For this feature to figure you’ll got to unscrew the tank and screw it back on again to detect the coil.
The menu and controls are very simple and appear to be aimed toward newer users, there’s no fancy features like temperature control (TC), bypass (BP) or maybe preheat settings which could postpone advanced users, personally I didn’t find this a con once I considered that the GTX ONE kit is meant to be an easy and effective fire and forget mod and tank. Most users don’t use advanced features, and for MTL vaping few of the advanced features make much difference.
The small OLED screen is extremely basic with the bare minimum of details on screen, it’s nice and bright and almost visible in daylight, overall no complaints here.
So anyway, back to the performance. Despite my already high expectations, it exceeded them and gave that rare WOW! factor. Finally I had found a pod beating MTL setup. It just about eliminated all my MTL stock coil tanks and AIOs (All in One) in one sweep.
I know too well that the shiny new toy novelty factor must be taken under consideration and that i tried to not get too excited by it. The flavour from the 1.2Ω mesh coil is superb . For anyone that has tried the OSMALL or XTRA then it’s considerably on par with those, vapour production is sweet and therefore the airflow is extremely smooth. At the recommended wattage, the vape is good and warm and keeps up well when chain vaping. Turning the wattage up to fifteen watts was obviously an excessive amount of because the vape got uncomfortable.
I absolutely hammered the primary coil and never got a touch of a dry hit. Flavour lasted goodbye and, as I wanted to check the 0.8Ω mesh coil, i ultimately swapped it over. I didn’t expect to enjoy the 0.8Ω mesh for MTL as once I tried this feature of the XTRA pod it had been more suited to DL (Direct Lung) vaping with a wider airflow, but i used to be to be proved wrong because it was a much more intense MTL vape, warm and it delivered such an honest throat hit using 6mg freebase. Equally I got a very good DL hit once I opened the airflow and therefore the vapour production was impressive, seems this coil may be a great all-rounder.
Though it wasn’t included within the kit, I also tested the 1.2Ω regular coil as a part of my GTX Coil review, I can’t quite put my finger thereon but i feel I prefer the regular over the mesh for a more traditional MTL vape. This was slightly surprising as I always considered mesh as king for flavour, but both 1.2Ω coils were equal though they offered a rather different vape, one worth consideration once you are ordering new GTX coils.
Lifespan of the included coils is great . I actually had to offer abreast of them because it would are too long to attend and obtain the review out. As it was, I’ve had over four weeks of normal to excessive use.
Vaporesso are certainly on a appear 2020. They were already churning out some great products (GEN, SWAG 2, PM80 etc.), except for me the most advancement has been with their coils and new wick making the bulk of latest products really stand out. Flavour and lifespan is what we’ve been crying out for, and Vaporesso appear to be listening.
Back onto the GTX ONE, this kit exceeded my wishes for a correct MTL stock coil tank and mod, adjustable airflow, simple, ergonomic, compact and lightweight enough to be pocket friendly with full bodied flavour.
For me, I don’t think the GTX ONE mod or tank are game changing for features or design, don’t get me wrong i feel they both look superb but I see them as re-inventing the wheel with superb refinements and getting it mostly right.
Bottom line is I genuinely love this kit and it’s a really welcome return to mod and tank setups for people who don’t like pods and AIOs. I actually enjoy decent pods, but you can’t beat a correct mod and tank, and that i can’t consider any pod that beats the GTX ONE’s vape quality for MTL.


Vaporesso Renova Zero My Points

The Renova Zero pod system has an elongated oval shape, measures 31mm x 13.5mm x 80mm and is primarily made from zinc alloy. I received the orange version for this review – which looks absolutely stunning – but the device comes in nine different colors, all of which have a matte finish that minimizes fingerprint staining. Design-wise, the Renova Zero jogs my memory many the Wismec Motiv 2 pod system. In fact, the primary time I saw the Zero, i used to be convinced that it had been Wismec’s newest generation vape pod, but it seems that the similar design is that the only thing these two devices have in common. Smok Nord Kit Pod System
Like most pod systems, the new Renova Zero is formed from the battery section and a detachable, refillable pod. The pod has magnetic contacts on rock bottom , so you want only drop it into the loading bay on the battery and it snaps into place. It’s draw activated, so all you’d wish to aim to to is suck on the mouthpiece of the pod after you’ve filled it and it’ll start to heat the coil inside. But first, you’d wish to point out it on, which leads us thereto tiny button on the battery.
The overwhelming majority of pod systems are automatic, so as that they don’t have any buttons, but the Zero by Renova could even be slightly different. It’s also an automatic, regulated vaping device, but it also features alittle round button on the battery which does some cool stuff. First of all, you’ll click that tiny button five times in rapid succession to means the battery on or off. this allows you to draw on the mouthpiece without accidentally activating the battery, just just just just in case you’d wish to ascertain something. But there’s tons more thereto than that.
One of the items that sets the Renova Zero aside from virtually all other pod systems is that the built-in variable wattage feature. Pressing that very same plastic button 3 times rapidly, will cause the colour of the build-in LED to chance to either green, blue or yellow, each kind of a special wattage level. Green is 12.5W, blue is 10.5W and red is 9W. Although there’s no due to adjust the airflow on this device, the variable wattage function allows you to manage the vapor production also because the temperature of the vapor. The differences between the three available settings aren’t huge, but thy are definitely noticeable. Simply pressing the button just one occasion will cause it to illuminate in one among the three colors (green, blue, red) letting you recognize the wattage level it’s currently at, so you’ll change it if you’d wish to .
The button on the battery also acts as a classic battery level indicator. It lights up whenever you draw on the mouthpiece of the pod, and thus the color it lights up in corresponds to the facility left within the battery. A green light allows you to know that battery life is over 70 percent, blue means it’s between 70 percent and 30 percent, while red means it’s under 30 percent. The Renova Zero could even be a regulated vaping device, so you shouldn’t notice any difference in power output no matter battery life. However, when the battery is almost depleted, you’ll definitely notice a drop by vapor production.
There’s more innovation during this small button of the Renova Zero than I’ve seen altogether pods I’ve reviewed, but there’s actually more to travel over. as an example , the Zero pods have an innovative push-to-fill refilling system which eliminates the necessity for rubber plugs. Basically, there’s this small metallic funnel on rock bottom of the pods which you’d wish to depress on when filling. It actually requires some pressure, so pressing down with a glass dropper isn’t advisable, because it’s getting to crack, so Renova actually included a fine tip refill bottle. If you’ve already got one among those thin tip unicorn or gorilla bottles, you don’t actually need the included refill bottle, but it’s nice that they’re offering it anyway.
This innovative refill system has been working excellently thus far . albeit there’s no visible plug stopping the juice from leaking out of the pod, the fill port is as dry as a bone immediately , so I’m willing to bet that we’ll be seeing more of it within the long run . Vaporesso Renova Zero Pod Cartridge
Finally, the Omni Board Mini chip powering the Renova Zero also features temperature control technology, which I’ve never seen used on a pod system before. While you’re unable to line the temperature or the TCR, like on advanced vape mods, this handy feature prevents users from accidentally burning the coil inside the refillable pod and thus ruining it. When the chip detects that there isn’t enough e-liquid left inside the pod to saturate the wick round the ceramic coil, it cuts off power from the battery. That’s one among the good features I’ve seen on a pod system, and definitely one I’d wish to ascertain implemented on other devices also .
All in all, from the ergonomic, pocket-friendly design and quality paint job, to the multitude of innovative features, the Renova Zero vape pod left me impressed. In fact, it’s so initially else I’ve used that I’m having trouble even comparing it to other pod systems.
The Renova Zero is shorter than the Wismec Motiv 2 and slightly thinner than the SMOK Novo vape pod, so i used to be surprised that it’s a considerably higher battery capacity. The Zero features a 650mAh built-in battery which is nothing in need of wonderful for a tool this compact. How long it’ll last you depends on a variety of things , from what proportion you vape to what wattage putput you’re using it in, but one thing is needless to say , it’ll keep you vaping tons longer than the 150mAh JUUL.
You’ll even be happy to understand that the Renova Zero features fast-charging technology (1 amp charging rate) which allows you to completely recharge the battery in about 45 minutes. If that’s still too long, you’ll also use it while it’s charging, which may be a huge plus, considering many vape pods don’t have passthrough functionality.
I’ve been using the Renova Zero for nearly hebdomadally , then far I’ve been very pleased with the way it’s been performing. The draw is what i’d call middle-of-the-road, to not loose, not too tight, which is essentially ideal for such a customizable device. Having too tight a draw would have negated the potential of the adjustable wattage function, a minimum of in terms of vapor production, and making it too airy would have made it disappointing for mouth-to-lung vapers. This way, it’s an honest compromise which may please most users.
The Renova Zero pods accompany a built-in 1-ohm ceramic Ccell coil which really brings out the flavour of the e-liquid. It’s not nearly nearly nearly as good as a triple mesh-coil tank, a touch just like the Freemax Mesh Pro, but compared to other pod systems, the taste is extremely clean. Another advantage of this ceramic coil is that it’s alleged to last longer than cotton wicked ones. I’ve only been using it for every week , but I expect to urge a minimum of another seven days out of it, especially since i’m employing a transparent , very lightly sweetened juice.
One thing to stay in mind with the Renova Zero is that when using it at max power output (12.5W), it tends to burn through e-liquid tons faster than regular pod systems. You get some impressive plumes of vapor, but you’ve to buy for them in e-liquid.
As I already mentioned, I’ve had no leaking issues with this device, the coil has been holding up well and flavor is best than I expected. One very small con would be that the draw activated switch isn’t the foremost sensitive I’ve seen, so you actually need to suck on the mouthpiece of the pod to activate the battery. But aside from that, I even have no problems to report.
I’ve used dozens of pod systems within the last year alone, and I’ve liked some quite others, but aside from the standard differences in design airflow and battery capacity, there wasn’t tons setting them apart. The Renova Zero is during a league of its own therein regard. Not only is it a solid device that basically performs alright , but it also introduces some truly innovative features, from the new push-to-fill system, to the variable power output and temperature control. this is often often often without a doubt the foremost advanced vape pod system I even have ever used, which alone is worth your money.
The Renova Zero was sent to me by Buy Best, for the aim of this review. They currently have it on sale for just $17.99.

My Review MECHLYFE Replacement RBA Coil Head

The first Impressions for Voopoo Vinci and Vinci X Devices
Both the RBA Coils are very very small in size with the Build Deck even smaller. Both of these cost around 4-5 USD each. Both come with Spares and Coils in the Box with a little cotton, a Screwdriver and Spare Build Deck Screws. Both RBA’s have 510 connections so you can dry burn and remove hotspots on a Mod.
Plug and Play VXV 510 Adapter
Both RBA’s come with Bottom Adjustable Airflow control , (However i noticed that on the Yachtvape RBA you cango a bit more Tighter Draw than the Mechlyfe which has a Medium loose MTL Draw)The max Build Diameter you can go is 2.5mm , but 2mm would be perfect in my humble opinion.Little Difficult to Build as the screws are too tiny, but very easy to wick both RBA’s
Performance about them VOOPOO VINCI X Pod
Coil wire used – Coilology 28/40g N80 Wire (5-6 Wraps) 2mm ID (0.5 ohm at 15 Watts and 1.0 ohm at 12 Watts ) The Mechlyfe and Yachtvape RBA’s offer All round Excellent Flavor and Throat hit.
i have been using them both on the Voopoo Vinci 40watts and the Vinci X with 70:30 and 60:40 (12mg) ratio eliquids from the last 4 days now and there are zero issues whatsoever.
both the RBA’s have Zero leakage issues / no gurgling / no spitback till now.
The only noticeable difference between the Two RBA’s are, on the Yachtvape RBA you can adjust the airflow to a tight draw but the flavor and vapor suffer, hence i kept it medium loose and its been perfect.

Review Ehpro Cold Steel 100 Using Experience

Cold steel 100 is essentially a tube mod, but with rectangular blocks protruding from the sides. I think this is where fleas and all electronics. Ambitionz vaper written directly on top of the rectangular housing part, forgetting that it has been designed. This construction is different from the second tube or mod mod box and not a mixture of both. I admit that the thought first it seems a bit odd, but the design was more in me.

to keep one of the main reasons is because it is very easy. Just hand it is convenient and not comfortable in the least. Furthermore, if the trigger for index finger or thumb for the purpose of the press in an ideal position. Cold Steel 200

It consists of a combination of zinc alloy, brass and stainless steel, so it is a bit on the side hard. 178grams weight without the battery, but the weight does not really bother me; MOD feel much stronger and indestructible. I did not fall, but I think perhaps survival is fine if I do.

Given its size, it is a little shorter and thinner than average eJuice and 60ml bottles. I think it’s mod perfect size for a single battery case … Or mod Tube … Anyway, it was a good size!

So I never tested the product Ehpro my first experience with excellent build quality and happiness. This table is well maintained and comfort feels well built and solid. Even the “COLD STEEL” is made on the basis of the MOD clear and precise printing.

Plate 510 in tank 25 mm without extension folder, so it is large enough to accommodate most atomizer. tank 26mm slightly in spite of the position.

There are only three buttons on cold steel 100 and the change to the gap of the tube in a rectangular cross section. One of them is the fire button and the other two are for the setting. Button Wiggle bunting, but strong enough to dial a number. But they are very sensitive and works without problems.

I could not get a spot size OLED screens is collected, but it was small. Is it a black and white display for easy but amazingly bright and clear OLED. It has the basic information such as vaping mode, temperature / current, the battery, the resistance and voltage.